1UPKeyboards Discord

Join 1UPKeyboards Discord

https://discord.gg/AGuKen3

QFR Frosty Flake Controller

$35.00

In stock

Description

Turn your starter board into an endgame programmable keyboard with this!

The Frosty Flake, created by bpiphany, is a replacement controller that turns your CoolerMaster Storm QuickFire Rapid mechanical keyboard into a fully programmable keyboard. It’s built around an AVR microcontroller from Atmel, which is compatible with multiple ways to program your board including TMK and Easy AVR.

  • NO soldering required.
  • Easy installation.
  • A magnet is required (like a fridge magnet) to set the controller.

Please check your Keyboard’s PCB to ensure compatibility.

  • CST-IF87/88/89/91-MB V1.1 2011-07-26
  • CST-IF87/88/89/91-MB V2 2012-07-30
  • Quickfire_V2.1
  • Quickfire_V2.2

Each controller has been assembled and tested, and is plug (and magnet and program) and play.

PLEASE NOTE: THIS CONTROLLER WORKS WITH THE CM STORM QUICKFIRE RAPID ONLY. YOU WILL NEED TO VOID YOUR COOLERMASTER WARRANTY TO USE THIS PRODUCT. INCORRECT ALIGNMENT OF THE PINS WILL DESTROY YOUR BOARD. WE TAKE NO RESPONSIBILITY.

***FREE shipping within the CONUS***

Watch our installation and setup video:

Download the Easy AVR USB Keyboard Firmware and Keymapper here

Don’t already have the CoolerMaster QuickFire Rapid, get one here

Instructions for Mac ONLY:

This is where you will create all of your macros. Once you have created all of your macros, you need to save the .hex file.

Next, you’ll need to install dfu programmer by following these steps in Terminal – http://macappstore.org/dfu-programmer/

Now plug in your keyboard with the Frosty Flake and run a magnet over the Frosty Flake to set it into boot mode.

Next, navigating in Terminal, go to the directory where you saved the .hex file and run each one of these codes:

sudo dfu-programmer atmega32u2 erase
sudo dfu-programmer atmega32u2 flash “the file you saved”.hex
sudo dfu-programmer atmega32u2 reset


Your Frosty Flake should now be programmed with all of your macros. These stay with your keyboard, so when you change computers all of your macros will still be there.

TIP: You can set up a key to set your Flake into boot mode, so you won’t need to use the magnet the next time.

Description

Turn your starter board into an endgame programmable keyboard with this!

The Frosty Flake, created by bpiphany, is a replacement controller that turns your CoolerMaster Storm QuickFire Rapid mechanical keyboard into a fully programmable keyboard. It’s built around an AVR microcontroller from Atmel, which is compatible with multiple ways to program your board including TMK and Easy AVR.

  • NO soldering required.
  • Easy installation.
  • A magnet is required (like a fridge magnet) to set the controller.

Please check your Keyboard’s PCB to ensure compatibility.

  • CST-IF87/88/89/91-MB V1.1 2011-07-26
  • CST-IF87/88/89/91-MB V2 2012-07-30
  • Quickfire_V2.1
  • Quickfire_V2.2

Each controller has been assembled and tested, and is plug (and magnet and program) and play.

PLEASE NOTE: THIS CONTROLLER WORKS WITH THE CM STORM QUICKFIRE RAPID ONLY. YOU WILL NEED TO VOID YOUR COOLERMASTER WARRANTY TO USE THIS PRODUCT. INCORRECT ALIGNMENT OF THE PINS WILL DESTROY YOUR BOARD. WE TAKE NO RESPONSIBILITY.

***FREE shipping within the CONUS***

Watch our installation and setup video:

Download the Easy AVR USB Keyboard Firmware and Keymapper here

Don’t already have the CoolerMaster QuickFire Rapid, get one here

Instructions for Mac ONLY:

This is where you will create all of your macros. Once you have created all of your macros, you need to save the .hex file.

Next, you’ll need to install dfu programmer by following these steps in Terminal – http://macappstore.org/dfu-programmer/

Now plug in your keyboard with the Frosty Flake and run a magnet over the Frosty Flake to set it into boot mode.

Next, navigating in Terminal, go to the directory where you saved the .hex file and run each one of these codes:

sudo dfu-programmer atmega32u2 erase
sudo dfu-programmer atmega32u2 flash “the file you saved”.hex
sudo dfu-programmer atmega32u2 reset


Your Frosty Flake should now be programmed with all of your macros. These stay with your keyboard, so when you change computers all of your macros will still be there.

TIP: You can set up a key to set your Flake into boot mode, so you won’t need to use the magnet the next time.

Additional information

Weight 0.2 lbs
Dimensions 5 × 3 × 1 in

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Pin It on Pinterest